The mini-tray was designed as an alternative to the standard JEDEC tray for semiconductors. It has the same width as a JEDEC tray, but its length is a third of that of a JEDEC tray. Thus, three mini-trays lined up have the same width/length dimensions as one JEDEC tray (the mini-tray is 0.85 mm thinner than a JEDEC tray).
JEDEC trays are optimized for purposes of mass production of electronics. The design of the mini-tray aims at small-scale production and storage of small series of components. Small pick-&-place have limited space for trays, sometimes only a single one. Mini-trays then allow for three times as many different tray-packaged components in a single project.
With JEDEC trays, an empty tray serves as a lid for a full tray. The reason for this choice is that the idea is that you stack up to 20 full trays. Each full tray is the lid for the tray below it. The large pick-&-place machines can unstack trays automatically, so you put the entire stack in the machine. So for storage and transport, using an empty tray as a lid for the topmost tray in the stack is a straightforward solution.
While mini-trays can stack, no pick-&-place machine to date can unstack them, nor is it likely that one ever will. You can still use an empty mini-tray as a lid for a full mini-tray, but for convenience there exists a mini-tray lid (or “cover”). The advantage is that the dedicated lid is thinner and that it does not obscure the tab of the tray: this tab is where you will put a label with the part number or description.
The mini-tray is also designed to have a magnet in each of the four corners, so that the lid snaps on the tray (and the mini-trays snap together). There is thus less risk that the components can “wiggle” out of their pockets while you are handling a stack. For storage, it is still recommended to also add a rubber band around a mini-tray with lid.
The relatively small size and the more common width/height ratio of the mini-tray makes it fit well in standard 127 mm × 152 mm anti-static sealed bags, together with a small bag with silica gel. These bags are available with grip-lock closing, and so they are reusable.
Like the JEDEC trays, mini-trays have a chamfered corner to indicate orientation. The step sizes (from pocket to pocket) in the horizontal and vertical direction are also copied from JEDEC trays (with three exceptions, see the table below).
The body size in the table excludes the pins; it is the nominal size of the body as given in the datasheet for the component. In practice, pins for TQFP, LPQFP and other members of the QFP family, are 1 mm long.
1 [Changed from 25.40 - JEDEC QFP 14×20]^ 2 [Changed from 25.20 - JEDEC QFP 20×20]^ 3 [Changed from 50.56 - JEDEC QFP 40×40]^
Type Body size Thickness Columns Rows X-step Y-step QFP 5×5 0.5 ~ 1.7 12 9 10.50 10.10 QFP 7×7 0.5 ~ 1.7 10 8 12.60 12.20 QFP 10×10 0.5 ~ 1.7 8 6 15.70 15.20 QFP 12×12 0.5 ~ 1.7 7 5 18.00 17.90 QFP 14×14 0.5 ~ 1.7 6 4 21.00 20.30 QFP 14×20 0.5 ~ 1.7 6 4 21.00 24.401 QFP 20×20 0.5 ~ 1.7 5 4 25.40 24.402 QFP 24×24 0.5 ~ 1.7 4 3 31.50 30.40 QFP 28×28 0.5 ~ 1.7 4 3 32.20 32.20 QFP 32×32 0.5 ~ 1.7 3 2 41.48 37.82 QFP 40×40 0.5 ~ 1.7 2 2 77.46 46.003 QFN 3×3 0.4 ~ 1.0 14 11 9.20 8.80 QFN 4×4 0.4 ~ 1.0 14 11 9.20 8.80 QFN 5×5 0.4 ~ 1.2 14 11 9.20 8.80 QFN 6×6 0.5 ~ 1.4 14 11 9.20 8.80 QFN 7×7 0.5 ~ 1.4 10 8 12.80 11.80 QFN 8×8 0.5 ~ 1.4 10 8 12.80 11.80 QFN 9×9 0.5 ~ 1.4 10 8 12.80 11.80 QFN 10×10 0.5 ~ 1.4 8 6 16.00 14.65
The height of the mini-tray is 5.5 mm; however the stacking height is 4 mm. The bottom of the tray, with the honeycomb mesh, sinks 1.5 mm into a lowered top surface of the tray below it. That is, when two mini-trays are stacked together, the total height is 9.5 mm (5.5 + 4 mm).
The lowered surface mentioned above is the platter. The platter has the pockets in which the components sit. In the middle of a pocket is a raised square, called the support. The idea behind this support is that the pocket is deeper at the edges than in the middle, to avoid pressure in the relatively frail gull-wing leads of components. Obviously this is only relevant for components with gull-wing leads, but mini-trays for “no-lead” components also have a support in the middle of a pocket, to keep the design uniform.
The honeycomb mesh extends below the frame of the tray by 1.5 mm. This is the part that sinks into the top of the tray below it. However, the platter is lowered more than 1.5 mm from the top of the tray. There is a gap between the top of the platter and the bottom of the tray that covers it. This gap, or separation, is typically 0.5 mm, but it may be less for mini-trays designed for very thin components. The separation should always be less than the minimum height of the component that it is designed for, otherwise the components might wiggle out of their pockets.
The depth of a pocket (measured at the support, not at the edge) plus the separation (discussed above) determines the maximum thickness for a component in the mini-tray. These design parameters define the component thickness range that a tray is suitable for: separation → minimum thickness, separation + pocket-depth → maximum thickness. These are the parameters that you can play around with, when you are making your own mini-tray layouts.
There is a tab on the top edge of the mini-tray. By convention, this holds some texts on the type, size and features of the tray. I only put the package style and body size on it (where QFP is generic for TQFP, LPQFP, VQFP and others). The rest of the tab is then available for a label with the manufacturer part number, for example.
The design of the mini-tray is in OpenSCAD. Via the OpenSCAD “Customizer”, you can select to print either the mini-tray or the lid. When choosing the mini-tray, you have the choice to either print it as a single part or as two parts, and you may optionally also print the label text separately. See the section “Printing recommendations” for more information. The OpenSCAD source file has quite a few options. There are pre-configured settings for common packages, but you can also make a mini-tray for a SOT223 package, for example.
All print files are in the 3MF format, as these are more compact than STL files and they also store configuration settings. Print files are provided for both a 1-part print (with supports) and a 2-part print (which must then be glued together).
All print files can be generated from the OpenSCAD source file. The source file has a few more pre-set configurations, for the less common shapes.
Description File OpenSCAD source files minitray_source.zip 3MF file for the mini-tray cover minitray_cover.3mf 3MF file for QFN 5×5 mm, single part minitray_qfn5x5_combined.3mf 3MF file for QFN 5×5 mm, two parts minitray_qfn5x5_separate.3mf 3MF file for QFN 6×6 mm, single part minitray_qfn6x6_combined.3mf 3MF file for QFN 6×6 mm, two parts minitray_qfn6x6_separate.3mf 3MF file for QFN 7×7 mm, single part minitray_qfn7x7_combined.3mf 3MF file for QFN 7×7 mm, two parts minitray_qfn7x7_separate.3mf 3MF file for QFN 8×8 mm, single part minitray_qfn8x8_combined.3mf 3MF file for QFN 8×8 mm, two parts minitray_qfn8x8_separate.3mf 3MF file for QFN 9×9 mm, single part minitray_qfn9x9_combined.3mf 3MF file for QFN 9×9 mm, two parts minitray_qfn9x9_separate.3mf 3MF file for QFN 10×10 mm, single part minitray_qfn10x10_combined.3mf 3MF file for QFN 10×10 mm, two parts minitray_qfn10x10_separate.3mf 3MF file for QFP 5×5 mm, single part minitray_qfp5x5_combined.3mf 3MF file for QFP 5×5 mm, two parts minitray_qfp5x5_separate.3mf 3MF file for QFP 7×7 mm, single part minitray_qfp7x7_combined.3mf 3MF file for QFP 7×7 mm, two parts minitray_qfp7x7_separate.3mf 3MF file for QFP 10×10 mm, single part minitray_qfp10x10_combined.3mf 3MF file for QFP 10×10 mm, two parts minitray_qfp10x10_separate.3mf 3MF file for QFP 12×12 mm, single part minitray_qfp12x12_combined.3mf 3MF file for QFP 12×12 mm, two parts minitray_qfp12x12_separate.3mf 3MF file for QFP 14×14 mm, single part minitray_qfp14x14_combined.3mf 3MF file for QFP 14×14 mm, two parts minitray_qfp14x14_separate.3mf 3MF file for QFP 20×20 mm, single part minitray_qfp20x20_combined.3mf 3MF file for QFP 20×20 mm, two parts minitray_qfp20x20_separate.3mf
An ESD-safe plastic is highly recommended. These plastics may also be called anti-static, dissipative or conductive.
A mini-tray can be printed as a single part, but this requires that you add supports. The alternative is to print the frame and bottom part as separate objects, and glue them together. In this latter case, the design has a small rim in the “frame” (the part with the large rectangular hole in the middle), where the bottom part sinks into to just the right depth. The lid (or cover) is printed as a single piece, and it is universal for all mini-tray sizes.
There are four holes in the corners of the mini-tray. These holes are specified in the design as 2.1 mm diameter. Due to the nature of 3D printing, they will typically come out a little smaller; the holes are intended for magnets of ⌀2×4 mm (⌀2×2 mm magnets in the lid).
You cannot use an automatic JEDEC tray exchanger on mini-trays. Automatic tray exchange (“unstacking”) was not a design goal for the mini-trays.
With regards to baking, only polycarbonate (PC) has a sufficient heat deflection temperature to create a “high-temperature” carrier, suitable for baking at 125 °C. 3D printed mini-trays of PETG, ABS or (especially) PLA must be considered “low-temperature carriers” (for use in drying cabinets with a baking temperature of 40 °C).